What is barge rafter mean

1. One of the two rafters that support that part of a gable roof which projects beyond the gable wall. 2. One of the rafters (under the barge course) which serve as grounds for the barge boards and carry the plastering or boarding of the soffits; also called a barge rafter.

What is a barge in framing?

A barge board is the wooden board found on a home that runs up the A frame of a gable. … A barge board is the finished product of a gable, not the end rafter or the exterior rafter. Once you put in your end rafters, you would put one up to cover the rafters up for weatherproofing.

Is a barge a boat?

A barge is a kind of cargo-carrying vessel designed to transport passengers or goods through rivers or canals. Normally, these shipping vessels are long, flat-bottomed boats that do not have a self-propelling mechanism. A barge needs to be pulled by tow or a tug boat.

What is a barge board on a house?

What is a bargeboard? Bargeboards refer to the fascias located at the gable end or side of a roof. Used to protect the roof timbers of a building, bargeboards can also have a significant impact on the general aesthetics of the exterior of your property.

How much does it cost to replace rafter tails?

Eave PartReplacement Cost (Labor Included)Rafter Tail$3 – $9/board footRoof Gutters$3.65 – $30.85/linear foot

What is the difference between a hip Jack rafter and a common rafter?

COMMON RAFTER: A rafter that runs perpendicular (90°) from the wall plate to the roof ridge when looking straight down at the roof. … HIP JACK RAFTER: A rafter that runs from the top of the wall plate to a hip rafter at 90° to the wall plate (see Figures 1, 8 and 14).

What is rafter tails on a roof?

Rafter tails are the exposed exterior portion of a building’s wood structural truss that projects beyond the perimeter wall of the structure. … We call them Rafter tails because they are the tail end or exposed end of a rafter.

What is a barge on a roof?

BARGE BOARD – The board covering the roof timbers on the gable or skillion end of a roof, fixed parallel to the roof slope. BATTEN – A batten is a piece of timber or metal channel installed horizontally on top of the rafters to allow sheet metal to be laid and fastened.

How much should a roof overhang?

Overhangs can vary from a few inches to a few feet depending on preference; however, the suggested width of an overhang is between 12” and 18” for eaves and no more than 8” for rakes. That said, overhangs can extend as far as 2′ without the need for external supports.

Where is the barge on a roof?

For the uninitiated I had better explain that the “barge” refers to a roof/side wall junction where the wall extends up just above the roof and is covered with a band of concrete.

Article first time published on

What is the difference between a fascia and a barge board?

Bargeboards and fascia boards are essentially the same thing. They are both long, straight boards that run along the lower edge of the roof. However, fascia boards run horizontally, carry the gutters and support the bottom row of roof tiles. Bargeboards run diagonally and are located at the gable end of a property.

What are fly rafters?

A fly rafter is attached to the overhang of your roof. It extends beyond the end of the rafter, if necessary. Fly rafters help keep the plywood or other type of roof sheathing straight. The size of a fly rafter can vary depending on personal preference, but should be slightly smaller then the regular roof rafters.

What are fascia boards and soffits?

Fascia, or fascia boards, are long straight boards that are found at the lower edge of the roof and is fixed directly to roof trusses. … Like soffits, fascias do two jobs – they finish the look of the house and protect the interior from weathering damage.

How do I install lookouts?

Go to your app market and search for “Lookout” (Google Play Store or iOS App Store) Select “Install” or “Download” when you’re given the option. Once installed, open the Lookout app on your phone and you will be asked to create an account with an email address for your username, and a password of your choice.

Are barges self-propelled?

Put into its most basic terms, a barge is a boat (usually with a flat bottom) that is primarily used to transport goods through rivers and canals. While these boats can sometimes be self-propelled and move on their own, barges are almost always pulled by a tow or a tugboat.

Are barges seaworthy?

Although there are barges that are used in open ocean waters they are not seaworthy vessels. … This is because the barge was never designed for ocean use. In fact, the barge wasn’t even designed to be used in deep water.

What is the difference between barge and boat?

is that barge is a large flat-bottomed towed or self-propelled boat used mainly for river and canal transport of heavy goods or bulk cargo while boat is a craft used for transportation of goods, fishing, racing, recreational cruising, or military use on or in the water, propelled by oars or outboard motor or inboard …

How do you replace a rafter without removing the roof?

1. Measure the dimensions of the old rafters beneath your roofing surface. …
2. Slide one of the newly cut rafter legs into position directly next to the old rafter. …
3. Slide the new joists into position beneath each of the new sets of rafters.

How do you repair a rotted roof rafter?

1. Remove the rotted wood with a chisel and pry bar. …
2. Measure the length of framing wood needed with a measuring tape. …
3. Cut the framing wood to fit with a circular saw. …
4. Cut sister boards if necessary with a circular saw. …
5. Screw the new rafter into place.

Are rafter tails expensive?

The cost is approximately $60 per “tail”.

What is false rafter?

A false rafter is a type of rafter extension used in building framing systems.

What is a cripple Jack rafter?

Cripple Jack Rafter: A rafter that runs from the hip to the. valley perpendicular to the ridge. (See figures 1 and 14) Dormer Rafter: A rafter that sets on top of the main roof without cutting into the main roof.

What type of roof calls for both hip and valley rafters?

A hip rafter is called for only when framing a hip roof, but a valley rafter is needed on both hip and gable roofs whenever roof planes intersect. A jack rafter is a shortened com- mon rafter that may be framed to a hip rafter, a valley rafter, or both. Thus, there are hip jack rafters and valley jack rafters.

What is valley rafter?

Definition of valley rafter : the rafter running from the wall plate to the ridge and along the valley of a valley roof.

Are roof eaves necessary?

Eaves are ubiquitous in most traditional architecture, and in addition to their aesthetic role, they serve several important functions, the primary one being to keep rainwater away from the building’s walls and structure. … However, eaves are not an indispensable component of a building.

What are standard roof pitches?

The most commonly used roof pitches fall in a range between 4/12 and 9/12. Pitches lower than 4/12 have a slight angle, and they are defined as low-slope roofs. Pitches of less than 2/12 are considered flat roofs, even though they may be very slightly angled.

What is the overhang of a roof called?

What Is a Soffit? Your roof by necessity, will often times extend over the walls of your home. This overhang can go by a few names, such as the house eaves or the rafters of your roof. The underside of this overhang, when given a finished appearance, is known as the soffit, which means “something fixed underneath”.

What is a barge on a shed?

Barge Capping : Barges, Barge cap etc are the typically right angled flashings installed at each end wall of a shed where the end wall sheets meet the roof sheeting and a water proof capping is required to seal the shed. They are available in different designs to suit different needs and tastes.

What is a barge gutter?

Barge gutters are designed to provide an option for the rainwater carrying capacity for the sides of buildings. This detail is the most common way to flash the side of a steel clad roof.

Why is it called barge board?

Bargeboard (probably from Medieval Latin bargus, or barcus, a scaffold, and not from the now obsolete synonym “vergeboard”) or rake fascia is a board fastened to the projecting gables of a roof to give them strength, protection, and to conceal the otherwise exposed end grain of the horizontal timbers or purlins of the …

Where do barge boards go?

A bargeboard is a type of long fascia board that is attached to the projecting gables of a roof in an inverted V-shape. They provide strength and protection from the weather to the ends of the roof rafters. Bargeboards also hide the ends of timber beams within the roof.